Jay's Adventures in 3D Printing

-=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- (c) WidthPadding Industries 1987 0\|106\|0 -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=- -=+=-
Socoder -> Off Topic -> Jay's Adventures in 3D Printing
Page : 1 2 3 Prev 4 Next
Mon, 19 Mar 2018, 11:12
Jayenkai	Rejigged tool, got exporter working, seems to be importing into the printer converter doohickey program well enough.. Will be attempting a test print after The Chase..! -=-=- ''Load, Next List!''
Mon, 19 Mar 2018, 12:23
Jayenkai	Reminder to self.. those are mm not cm!!! -=-=- ''Load, Next List!''
Mon, 19 Mar 2018, 13:25
Jayenkai	(Note : The glow is merely a picture from the iPad underneath, glowing through the thin plastic!) Mmmmmm! Still not got everything I need!! Ffs!! Tomorrow, terps/white spirit, and a decent container, so I can wash out the wee paint brushes, and then itâ€™ll be a battle with shaky hands, as I attempt to paint my lovely little Platdude! -=-=- ''Load, Next List!''
Mon, 19 Mar 2018, 13:35
spinal	*Like
Wed, 21 Mar 2018, 10:11
Jayenkai	Been putting this stage off for long enough. First coat, not too bad considering it's been about 20 years since I last attempted this, and my hands arenâ€™t exactly the steadiest pair of hands in the world!! Second coat will be later (maybe tonight?) in which Iâ€™ll need to get closer to the edges, and define the lines a little better. -=-=- ''Load, Next List!''
Wed, 21 Mar 2018, 10:22
GfK	Looks good. What are all the diagonal lines tho? Is that the back?
Wed, 21 Mar 2018, 10:39
Jayenkai	Yeah, thatâ€™s the bottom when printed, so you can easily'ish tear away the stability base from the actual model. The other side, the paint isnâ€™t quite as nicely adhered to the surface and you can see streaks in it. This "bottom" looks WAY better than the other side!! Iâ€™ll be doing a second coat, neatening the edges and hopefully making the front look a bit better. Still happy with the result, though. \o/yeay\o/ for printing!! -=-=- ''Load, Next List!''
Wed, 21 Mar 2018, 10:48
GfK	Ah I see. Maybe give the painted side a light rub-down with a 2000 grit sandpaper to give the paint something to cling on to?
Wed, 21 Mar 2018, 10:52
Jayenkai	Good idea, yeah. Thereâ€™s probably oodles of techniques for this. I, as per usual, am simply ploughing ahead without looking -=-=- ''Load, Next List!''
Wed, 21 Mar 2018, 11:09
GfK	Well, the reason the back has covered so well is cos the surface is rougher. Ideally you'd sandpaper the surface you're going to paint with 1000 grit, cover it with spray primer, sand again with 2000 grit, then paint. If it's good enough for cars its good enough for Platdude. A lot of primers aren't good on plastic cos of the solvents but I think there's a Plastikote one that'd be perfect for this.
Thu, 22 Mar 2018, 07:00
Krakatomato	Jay - if you're still working on glass then I've found the perfect alternative to gluesticks! I knew hairsprays worked for many people but I've had issues trying to find one that worked well. That's no longer the case - if you have an Aldi near you then pick up a can of CARiNO Firm Hold (With Vitamin B5). They're around 89p each. Bargain. Make sure the glass is proper clean (soapy water) and dry. Then attach back to printer base and spray this stuff over. Heat the bed up and let it sit for a minute to dry out a little. Then go print away. The base underneath is perfectly smooth - no more weird gluestick texture Oh, and just let the bed temp drop when you're done and the print will just pop off in your hand without any effort!
Thu, 22 Mar 2018, 07:04
Jayenkai	I'm fine with these, thanks!! -=-=- ''Load, Next List!''
Thu, 22 Mar 2018, 07:10
Krakatomato	hahaha - perfect
Page : 1 2 3 Prev 4 Next